Tips For Replacing a Window Handle

It is simple to change your window handle from the comfort of your home. Follow these tips to ensure an elegant and smooth finish.

Remove the screws from your uPVC handle to reveal the screws. Measure the spindle's length to ensure that you get the correct size replacement.

1. Take a measurement of the Spindle Length

If you're replacing a window handle, it's important to get the size of the spindle correct. It can influence the tightness or looseness of the handle, as well as whether the handle locks correctly into the window frame. The spindle is a metallic shaft that connects the handle to the lock inside the window frame. The spindle can be found in the standard 8mm cross-section for industry or the older 9mm versions. Modern industry standards are 8mm, however it wasn't always the case. It is important to check the measurements when buying the handle you want to purchase.

Take the handle off. This is done by turning the handle in the open position and taking off two screws that secure the handle (which are usually concealed behind plastic caps that are required to be removed). Once the handle has been removed, take a measurement from the base to the end. This will provide you with the measurements needed to purchase a new one.

There are plenty of options when it comes to selecting the right window handle from sleek chrome that blends into a contemporary home to traditional brass with a burnished finish that looks great in restored Georgian rooms, or even the more classic Tudor cottages with curled monkey tail locks! There are many options, but the most important is to choose one that complements your home's decor.

Espag handles are typically fitted to uPVC window frames and are always the same size with a 43mm center. Cockspur handles are available in a variety of sizes, from 58mm up to 62mm. Window handles made of Cadenza have a different size because they have an angle blade that operates a multi-point lock mechanism inside the window.

Another consideration when selecting a new window handle is determining what hand you need to use, which is defined by what hand you use to open the door handle replacements. Inline Espag window handles aren't hand-operated and can be used for left or right handed windows. Cranked window handles are hand-operated and can only be used on windows that open in one direction.

2. Remove the Handle

A window handle that falls out is a frustrating experience, regardless of regardless of whether the handle has been damaged or worn out. The good part is that replacing a uPVC window handle is a simple job that you can do yourself. You only need some basic hand tools and some time to complete the process.

The first step is to need to open the window and ensure that it is in the unlocked position. Then, you need to remove the screw caps that hold the handle in place. Once the screw caps are removed you will be able remove the handle.

The handle is attached to a spindle inside the window frame. Based on the type it is held in place by a screw or a pin. The most commonly used handles are the inline Espagnolette and the cockspur handles. Both these types of handles are utilized on casement double glazed windows handles, as well as windows made of aluminium. They can be locked using keys to stop unauthorised opening of the window from the outside or you can lock them by turning the handle clockwise.

To take the handle off, you'll need an screwdriver with a flat blade in order to loosen the clip that holds the handle. Once the clip is released, the handle should be able to slide off the spindle. When the handle is removed, you'll need to measure the length of the spindle and make sure that the new handle is compatible with the spindle's length.

Once you have the right size, you can screw the new handle in the correct position. It is important to ensure that the new handle is firmly attached and that it turns in the correct direction (clockwise for open, or counterclockwise for closed). It is also essential to check that it is not installed upside down.

Finally, you should replace the screw cover caps. After you've done this you can test the handle to make sure that it functions properly. You can also test the locking mechanism by moving the handle from the unlocked position to the locked position and then back.

3. Take off the Screws

A uPVC window handle is a crucial element of any home and is often the first thing to show signs of wear and tear or damage. This could be due to natural causes, frequent use or even intentional damage by criminals looking to gain access to your home. However, a simple repair is a simple solution and prevent the issue from happening again.

uPVC handles could also be difficult to remove if the locking mechanisms are not working properly. Most of the time, the issue can be resolved by replacing the multipoint lock rather than the entire handle and it's definitely worth a look since it can save you money.

After removing the old handle, you'll have to take off any screws that were holding it in place. These are typically located on the inside face of the handle base. You may need to use an screwdriver to do this, and it's essential that you don't over tighten, as this could cause the handle to become loose.

Then, you'll need to find the pins or screws that hold the handle in place. They will likely be found on the inside of the base of the handle and you will need to use an screwdriver or a pair of pliers to take them off them. If you'd like to, you can replace the screw caps and test the handle to make sure it works correctly.

When you're ready for installing the new handle, simply line up the spindle with the cutout in the window mechanism and screw it in the appropriate position. Make sure that the handle is in the open position and that any screws are tightly fixed before replacing the screws' covers, if you wished to do this. Once this is complete you're all done and you can enjoy your new window handle. I hope this will enable you avoid having to pay for costly window and double glazed door handles replacements in the future. If you'd like to get more help in this, or any other aspect of your uPVC windows do not hesitate to contact us.

4. Fit the New Handle

The replacement of a damaged window handle or updating it is simple and can be completed within just a few steps. The first step is to determine the type of handle, measure its spindle, and determine what tools you'll require to complete the task. Always prioritise the safety of your windows and tools. Take your time to follow the steps and ensure that you have the right handle to use.

The first step is to identify the screws holding your existing white window handles handle in place and remove them, while keeping an adequate grip on the handle itself to stop it from falling and result in injury. Once the screws have been removed, you can place them in a safe place to be replaced in the future.

After removing the old handle, you are now able to install your new one. It is essential that the handle fits perfectly to ensure that it is functional and secures the window in position. Next move the square metal bar on the handle into the hole in the window mechanism.

The last step is to replace the caps on the screws and test the handle to make sure it is working. If you are not satisfied with the result or if your window does not shut or open properly, call our experts for help.

The majority of UK homes have uPVC Windows. Therefore, a large number of windows will need to be changed at some point due to wear and tear or breakage. The process is relatively straightforward and can be carried out by anyone with some knowledge of DIY. It is crucial that the handle you use matches the dimensions tilt and turn window handles style of the window. Contact us if you are unsure about the type of handle you need. They will be able guide you through all the choices.