Replacement UPVC Door Handles

If you're replacing your handles or need to add extra security, you'll choose the perfect handle for your door. The upvc window locking handles handles are simple to install and will meet the required 92mm central distance for multipoint locks.

The backplate fixing centre and the lever/keyhole dimensions are the most important measurements. Compare these measurements to your existing measurements prior to making a purchase.

Lever/Pad

Lever pad door handles consist of a lever handle on one side and a paddle-shaped handle on the other. They are designed to be used with key wind locks. However they can be affixed to multipoint split spindle door locks.

Our range of upvc handles lever pads are available in a wide range of finishes. These will be shown in the drop down list once you have found the right handle for your doors. Not all styles of handles are available in every finish and it is recommended to check the technical drawings and sizes sections for the specific product that you're looking for to ensure that you are getting the correct size and fit.

It is essential to ensure that when you choose a new set upvc lever pad handles, they match the PZ (distance from the handle spindle to the middle of the hole in the cylinder) of your multipoint door locks. This is because they need to be aligned in order for the doors to stay locked, regardless of whether you are looking from the inside or outside. The handles we offer are designed to work with most standard cylinder locks, however you should double glazed door handle-check prior to ordering.

You'll need to remove your existing handles and dismantle the lock case if upgrading to dual spindle levers for your handle since this will require an additional split inline cylinder. These can be bought separately, and we provide an entire technical diagram to look at in the images for each product.

It is a good idea to loosen the screws that hold your existing door handle and then inspect the mechanism. If the screws aren't loose enough, you may need to loosen them more. Then, you can remove the spindle from the handle and replace it with a new Upvc handle. It is crucial to make sure that the handle is in the right position prior to screwing it into place. You can do this by placing your finger between the frame, and the window handle repair to make sure that it's in the right position.

Lever/Lever

The lever handles for doors are used to operate a multi-point lock with a Euro cylinder. They can be found on a variety of double glazed door handle upvc doors, as well as on some aluminium and wooden doors. They have a lever inside and an outside paddle and are usually supplied in two types. Sprung - These include an internal spring cassette within the backplate, which helps bring the handle lever into the horizontal position. Non-sprung: These do NOT have a mechanism for bringing the handle lever into a horizontal position.

To fix a door handle lever that is sagging you'll need to locate the hole or detent access pin. It's typically an insignificant hole or protruding ring, or rectangle, located on the handle base plate. Once you have located it, loosen the set screw using the help of a screwdriver, and then remove it to release the lever and return it to the horizontal position.

Once the handle is in a horizontal position, you can put the screws back in place and tighten them to make sure the handle remains secure on the base plate. You may want to apply a threadlocking solution to the threads of screws to increase grip and prevent them from loosening over time.

Drooping lever door handles can be caused by a number of factors. The most common reason is that the fixings are too tight, causing the lever bearing to get tangled up against the door. It could also be that the levers aren't operated in a straight line and this is causing compression of the latch mechanism preventing it from fully springing back into operation.

Another common reason is that the sprung lever is not operating correctly and this is usually due to the sprung not being in the right position within the backplate. The simplest way to check this is to move the handle to check whether it changes to the horizontal position.

It is essential to fix any loose door handles immediately. This can cause excessive wear on the screws and the handle may even fall off the base plate. You should also tighten any loose screws regularly to stop them from becoming looser.

Lever/Snib

These old Upvc window handles handles are called "Snib handle sets" and have a snib lock button at the top of the door lever. If you don't have a dummy locking device then you can use this to secure the door. These door handles are fitted with a Fullex lock 68PZ. (68mm between spindle and the centre of the lock). We also have a selection of door handles with 68PZ from manufacturers like Ferco and Fab & Fix.

Changing your door handle is a cheap method to upgrade your home, whether you're replacing existing handles or fitting new ones on doors you've built in your house. There are a variety of styles of door handles made of upvc, including traditional lever on backplates, straight or curved short latch and knob handles with dummy handles for multi-point locks, that are perfect for French doors.

Rose door handles are circular or oval-shaped versions of lever-on-backplate handles. These door handles are characterized by a lever or knob that is attached to the backplate. The backplate can be removed for hidden fixing.

The handles are available in various finishes, including coloured and chrome finishes to complement your door and other hardware such as knobs, hinges and bolts. Some handles for upvc windows are equipped with a an grub screw that can be used to connect the knob or lever to the spindle. Other handles come with bathroom spindles that can be used to control bathroom locks and incorporate a thumbturn turn and release mechanism, perfect to use on doors for bathrooms.

Mortise

The tubular latch is most likely to be the culprit in the event that your door handle is stuck open. There may be a few reasons for this, the first being an unlubricated latch plate on the latch plate. It is possible to solve this issue by opening the door, spraying lubricant on the lock and handle. It could also be that the latch is loose from the backplate. This could be more problematic and would require a professional to fix.

A multipoint door handle is the ideal solution to solve the issue of a sticking door handle. These handles are attached to the faceplate and operated by a key or thumb turn knob that activates the cam that locks the deadbolt. The handles are available in various sizes to fit different types of uPVC door and in various attractive finishes that match existing hardware. The handles can be bought online or through an authorized locksmith in your area. They are easy to install with clear instructions.

If you want to replace the handle set, you'll have to know the PZ size of the cylinder. This is the distance from the edge of the door frame to the centre edge of the hole in the handle in millimetres. It is also important to know if your door has a hook style lock or a mortise-style lock. The most efficient way to locate the correct handle once you know the measurements is to use the brand filter on the website. This will narrow down your choices and allow you to choose the right size from there.

A typical set of handles includes the handle, a pair of different length screws as well as drill guides and installation instructions. Smarter versions, such as the Igloohome Smart Mortise 2+ include a mortice lock complete with keys. These are more sophisticated units that are best for professionals or highly skilled DIYers. Certain handle sets come with various accessories, such as weather strips that can be used to improve the appearance of the door.