Fitting a cat flap can appear daunting but it's simple by following the correct instructions. Firstly, determine how high you want the cat flap to be (on average the belly height). Then, mark this area on your door, and use the template provided to guide you when drilling.

If you have a young kitten you can prop the door open a bit and gradually push it to pass through. Reward it each time it goes through.

Measure the Door

A cat flap allows your pet to enter and exit your home at its convenience. This can help keep your cat flap installation cost near me healthy as it will ensure that it is exercising regularly and be able to go back inside when it is trapped outside in bad weather. This will cut down on the time you allow your cat out or in and make your home safer by notifying you when it has left.

However, it is essential that the flap for your cat is correctly fitted to prevent your pet from being able to escape through it or be pushed through by other animals (e.g. dogs). You should measure the height of your pet's stomach and the size of the doorway at your home to ensure the flap is at the proper height. If your cat is larger or shorter than the normal, you can adjust the flap's height by moving it up or down by a tiny amount.

Then, use a spirit-level to mark the middle of the door. This is where you'll install the flap. Then, using the mark as a guideline, cut out the shape of your flap with the help of a Jigsaw. Once you've cut the space, sand down the edges of the door to smooth the surfaces. Then drill any fixing holes needed.

Fitting a cat flap should not take more than two hours. The process is slightly more challenging if you need to put it in the case of a uPVC door or a composite one. This is because composite doors come in different thicknesses, which could affect the way holes are cut. This is the reason we recommend hiring a professional to complete the job, particularly when you've never dealt with glass before.

Measure Your cat flap glass door installation near me

A cat flap can spare you from listening to your pet meow for you to let it out or in. This is particularly helpful for cats that are inside during the winter months while you work.

It is important to measure your cat's measurements first before you begin the installation. While it may seem an easy task, it is important to get the measurement right or your cat may find it very difficult to use.

Firstly, make sure your cat is calm and not feeling stressed before you take the measurements. You'll need to put your cat in a position that they are unable to move. Also, make sure that the measuring tape is flat and not curved against their body. Keeping the measuring tape or ruler against their body from the top of their head to the base of their tail can allow you to determine an precise measurement.

Once you have your cat's measurements, it's time to look at the door to determine where to put the flap. The flap should be placed at the level of your cat's belly. This will allow them to walk through the door with minimal effort. This will also prevent the flap making lots of noise when it swings open and closed.

You must consider the thickness of the uPVC or composite door as well. While timber doors are of the same thickness, uPVC and composite doors may differ in their overall construction, which can make fitting the cat flap more difficult because you must make sure that the hole you cut is the right size for your pet.

You can make use of the template included in the instructions to mark the position of the hole on the door. This will allow you to determine the location where the opening should be, and also to make sure the template is placed correctly on the door. Using a spirit level to ensure that the template is sitting right against the door can be extremely helpful.

Cut the Flap

Before you can install your cat flap, you'll need to cut the door panel to create a space large enough to accommodate it. This can be a tricky job, and it is recommended that you seek the help of an expert cat flap fitter to complete this task should you not have the expertise or knowledge to tackle it yourself. You can also read the instructions included with the kit to learn how to do it correctly.

You can consider the height of your cat's or kitten's stomach as a guide. A good rule of thumb is to put the flap of your cat about 10 centimeters away from the ground since this is approximately the average height of the cat's belly. This way your cat can move through the flap comfortably and it will also give the other cats or neighbours who are snooping difficult time trying to leave or enter.

Draw the location of the cat flap on the door using a pencil. Then, if your kit includes a template for paper, place this over the door and use the markings to drill holes in each corner of the template. Then, you'll be able cut out the template shape and replace it with the cat flap.

You can install the cat flap yourself on the door made of wood or uPVC If you're comfortable with the use of a jigsaw. Be careful not to cut into the mullions or rails that run vertically of your door. You can use a Jigsaw to cut your panel into a square or circle, depending on how you want it. Be patient and don't make the jigsaw cut faster.

Once the hole has been cut, carefully place your cat flap in its new home. Make sure that it is firmly secured. If it features caps on the screws, then place them onto the protruding screws. Once the screws are in place, sand the rough edges of the cut then seal any gaps to ensure that there are no draughts coming into your home.

Place the Flap

If you have an ordinary cat flap, you can encourage your pet to go through it by placing a small amount cat food on the top of the door. You can also try pushing the cat through with your hands or a stick. Once your cat is accustomed to walking through the flap it will be able to come and go whenever it wants. This lets you let it in and out at any time it wants.

It is possible to fit a cat flap into a UPVC or glass door however it's not quite as straightforward as fitting one into a timber exterior door due to the fact that the UPVC doors and some glass doors don't have the same thickness. This could have a significant impact on how you cut the opening for the flap and can also affect whether your flap will fit properly once it's installed.

The mounting kit may include a template showing you where to drill holes. If the kit does not include a template, you are able to create one by yourself. When cutting, it's important to not push the jigsaw far enough to make a larger hole than is necessary in your door.

Certain cat flaps come in circular designs, which are more difficult to put in. If you have a circular flap it's essential to make sure the hole is in the proper position on your door because if it's not, your cat flap glass door installation near me will not be able to use the flap and could be stranded in the open all day (or even at night).

Certain models of cat flaps have locks that allow you to regulate the time your cat comes and goes. These are useful if your pet is afraid of leaving in the dark or coming back inside at night. They are also useful when you are working all day. Certain locks can be used for entry or exit, and others can be locked both ways. This is useful for sick or older cats who aren't keen to venture out in cold weather.